1964 Nova 2 door post Low Reserve

1964 Chevrolet Nova Description

Some recent newly installed details

INTERIOR

•CARPET SET

•SOUND DEADENING KIT, FLOOR PAN, DOORS, ROOF AND TRUNK

•REAR SEAT

•DOOR PANELS FRONT

•DOOR PANELS REAR

•KICK PANELS

•GLOVE BOX

•ARM RESTS

•ARM REST PADS

•HEADLINER

•HEADLINER BOWS

•REAR SEAT SHELF PROTECTOR

•WEATHER STRIP KIT

•REAR WINDOW GLASS RUBBER

•WINDSHIELD GLASS RUBBER

•TRUNK DIVIDER

•STEERING WHEEL

•COMPLETE NEW GUAGE SET

•DASH AND JAMS PAINTED GLOSS HUGGER ORANGE

•PIN STRIPE ON GLOVE BOX

•HEADLIGHT SWITCH

•IGNITION SWITCH

•DOOR HANDLES

•WINDOW CRANKS

•TINTED SIDE AND REAR WINDOWS

EXTERIOR

•EXTERIOR PANTED SATIN FINISH HUGGER ORANGE

•PIN STRIPE ON SIDES, HOOD AND TRUNK

•SIDE MOLDING AND EMBLEMS PAINTED SATIN BLACK

BODY

•STEEL 2" COWL HOOD

•4 SPEED SHIFT HUMP

•FRONT BUMPER FILLER

•RADIATOR SUPPORT

•GRILL

•HEADLAMP BEZELS

•HEADLAMP FILLER DRIVER

•TAIL LAMPS

•FLOOR PAN

•BUCKET SEAT BRACKETS

•REAR QUARTERS LF & RT

NEW FRONT AND REAR BUMPERS

TIRES AND RIMS

•FOOSE 17" RIMS, 7" IN FRONT AND 8" IN REAR

•ALL NEW RUBBER

DRIVE TRAN

•RAME RAIL TIE KIT

•REAR SHOCKS AIR

•LADDER BARS

•REAR SPRINGS

•SUBFRAME CONNECTORS

•TUBULAR FRONT END KIT

•COIL OVER FRONT SHOCKS

•FRONT DISK BRAKE CONVERSION

•POWER BRAKE KIT

MOTOR & TRANS

•SBC 350 NEW/REBUILD

The 350 4 bolt main engine block casting #14010207 with date code #J211 = October 21st 1981 started life as a 1 ton truck engine. Engine block and cylinder heads were hot tanked and inspected. New cam bearings along with new gallery plugs and casting/freeze plugs were installed throughout. Block was aligned bored and hot tank bored and honed to 0.060" over using block plates. Engine currently displaces 360 cubic inches.

Crankshaft casting #3932442 is a nodular iron medium journal (2.45"/2.10") X (3.48" stroke) crank; it was inspected and polished to 0.010" undersize on mains and journals.

Inspected and reconditioned the factory rods were fitted with new TRW forged aluminum pistons (+0.060" oversize 9.5 to 1 compression ratio) wrist pins and chrome molly piston rings.

New hydraulic camshaft, hydraulic lifters, chrome molly push rods, double roller timing chain with matching crank and camshaft gear set.

350/400 Cylinder Heads casting #462624 with 76cc combustion chambers and 1.94"/1.50" valves were rebuilt. Heads received a performance 3 angle valve job including new umbrella oil seals and exhaust valve rotators. Anodized aluminum 1.5 to 1 ratio roller rocker arms

Engine rebuild utilized Fel Pro Ultra Blue performance seals and gaskets throughout.

Additional components included are, a high pressure/high volume oil pump, Chevy II Heavy deep sump oil pan, Chrome plated timing chain cover, Weiand Stealth dual plenum aluminum high rise intake manifold, 360 degree adjustable aluminum thermostat housing, Moon mechanical analog temp gauge, Oil pressure sending unit, New Malloy Unilite electronic ignition distributer, Weiand aluminum low drag water pump, Billet aluminum crankshaft and water pump pulleys, JEGGS High-rise aluminum valve covers, 100 amp chrome alternator, mini high torque starter, alum radiator,

Engine was broke-in and Dynoed ata Speed Shop in September and is in perfect running condition. 290hp

•SAGINAW 4 SPEED W ALUM BELLHOUSING

•HURST COMPETITION PLUS SHIFTER

•FLYWHEEL

•ZOOM CLUTCH/PRESS PLATE

•STARTER

•ALTINANTOR

•COIL

•WIRES

•CARB

•TRIPLE PASS ALUMINUM RADIATOR

•OIL PAN

•MOTOR MOUNTS

•MISC. BRACKES, MOUNTS, LINKAGE

•BATTERY

•"PIPES" HEADER BACK BEHIND REAR WHEEL STAINLESS EXHAUST SYSTEM

DYNO.BREAK IN

I hate to lose this vehicle but I have way too many projects and very busy work life. I will assist loading if you are shipping but this is at your expense and vehicle is sold AS-IS.

Tons of great parts and very fun Hot Rod to rip around in.

Certified check, cash only within 24 hours of auction end.