1977 AMC Jeep CJ5 304 V8 NEW Fiberglass Body 3 speed 6" lift 35" tires Project

1977 Jeep CJ Description

We were rebuilding this 1977 AMC Jeep CJ5, V8 304, 3 Speed T-150Trans, Dana 20 t-cass

This was a jeep that was being built from the ground up, For trailing or minor mud bogging,

No junk or rusted parts on the jeep,

Has New Complete Fiberglass body parts and hard top, Long term project that now will not be completed,

Has been stored in doors,

Interior never reinstalled so the only holes in tub are the body mounts,

Tub, Fenders, Hood, Windshield Frame & hard top all in new condition, Zero Road time,

Has PROCAR Black Racing seat, and the special brackets to work with the jeep CJ5 floor pattern,

Seats are not New with this upgrade, but were installed New during a prior upgrade, In very good condition,

No back seat,
RARE ACME Special order, CJ5 fiberglass Hard Top in near new condition, (Paid $1500.00) Very hard to find,
35" BFG All terrains, Bought New, Never on the road, But have been in storage for few years now,

Starting to show some minor age cracks,
On Rare turbine rims, 5 on 5 1/2 x 8" wide, Ford / Jeep bolt pattern,

On stock axles, I was told locker front and rear, But have not been able to confirm this, FYI,
Frame is sold as a rock, Trans-fer case has been lowered 1 1/2"

Spring over axle kit has been installed, ( prior Build) as well as a 3 1/2 inch body lift,

Gives the jeep somewhere between a 6 or 7 inch lift,
This was not a rusted out, run down jeep, This was a running driving Street / Trail rig before being rebuilt from the ground up,
Seller, Going in a different direction,
Also, Have Clear, Green Michigan Title For the Jeep,

NEW FIBERGLASS TUB, Well over 2 grand with shipping,
New Fiberglass Fenders,
New Fiberglass Hood with SS hood hinges,
New Fiberglass Windshield, Glass is cracked,
98% like new RARE Jeep CJ5 ACME Hard Top, ( paid $1500.00)

Rear hatch works like new,

Steel Grille, Solid as a rock, Best to use steel grill to hold secure weight of the front of body,
Tires and rims, 35" BFG allterains,
Heavy duty 3 T 150 speed trans
Dana 20 T-cass

Both drive shafts are there and in place,

After market 28 Gallon Steel fuel tank, Put in prior build also,,

Good running 304 amc v8, not connected to wiring, water or gas, right now,

Motor was reconditioned during a prior build, aluminum intake, performer cam, 4 bbl carb,

MSD coil and distributor, Nice finned rocker covers,

It has side exhaust headers, out to side exhaust Super Trap Mufflers,

Remote oil filter relocation kit, Heavy duty radiator,

Custom 6 point roll cage, Front bar comes down to the front floor close to he windshield,

( Extras) I have Bright Aluminum diamond plate rear body corners, lower rocker covers, Door Sill covers,

and a stainless steel hood cold air vent cover, I was not sure if i was going to use them but i will

give with the jeep,

Some other minor new and used parts for this project,
Jeep is MOSTLY together, Just small stuff to do from here
Have well over $6000.00 in just all the new Fiberglass parts alone,

Well over $8000.00 nvested, in the jeep project this time round, Not including prior work done last time

we upgraded jeep, or the original purchase price of jeep back when,

I WILL TRY AND POST AS MANY PICTURE AS POSSIBLE,

EBAY ONLY LET YOU POST SO MANY,

BUT IF ANYONE WANT TO SEE SOMETHING ELSE OR HAS A QUESTION,

PLEASE FEEL FREE TO CONTACT ME,

We have a Clear green Michigan title in hand for the jeep,

$500.00 DEPOSIT DUE AT THE END OF THE AUCTION,

BALANCE DUE ON PICK UP IN CASH,

OR YOU CAN SEND A CERTIFIED CHECK AND WHEN IT CLEARS BANK YOU MAY PICK UP JEEP,